INSDRAW LS11 A multi-purpose fully synthetic copper wire drawing lubricant
INSDRAW LS11一种全合成型多用途铜拉丝润滑剂
DESCRIPTION 产品描述
A Combination of specially designed additives have been used to produce a synthetic lubricant with
exceptionally high lubricity and anti-wear properties. The product was also designed to overcome
some of the historic issues associated when using synthetics, especially corrosion of machine parts.
INSDRAW LS11 是一种由多种特殊润滑添加剂组成的全合成型拉丝润滑剂。具有优良的润滑性和抗磨性。该产品的防锈性良好,可以很好的克服传统全合成型铜拉丝产品造成的机器零件腐蚀的问题。
APPLICATIONS 应用
The properties built into INSDRAW LS11 allow for a wide range of uses.
INSDRAW LS11可适用于以下场合:
- Superfine copper wire 超细铜线
- Fine copper wire 细铜线
- Suitable for both single and multi-wire drawing machines适用于单线和多线拉丝机
- Eminently suitable for enameled wire manufacture非常适合漆包线制造
- Plated wires and alloy wires 电镀线和合金线
- Precious metal wires 贵重金属线
PRODUCT HIGHTLIGHTS 产品亮点
- Excellent lubrication and corrosion inhibition performance 优秀的润滑性和腐蚀抑制性能
- Overcome issues with wire sticky dies and cones 克服粘丝模具和锥体的问题
- Excellent detergency helps wash copper particles back to the filter /lubricant holding tank
***去污力有助于将铜颗粒冲回过滤器/润滑剂收集箱
- Wire produced is smooth, clean and bright 生产的电线光滑、干净、光亮
- Production boosted due to reduction in wire breaks and downtime 减少电线断裂和停机时间,增加产量
RECOMMENDED INSTRUCTIONS FOR USE 推荐使用
- Before preparing a solution of INSDRAW LS11 for use ensure the complete lubricating system is
clean and free of any oily residues.
在准备使用 INSDRAW LS11溶液之前,需确保整个润滑系统干净,没有任何油性残留物。
- Where wire surface cleanliness and brightness is a key factor it is recommended to use deionized
water for preparing the solution and subsequent top up. Maximum recommended hardness of
water is 150ppm CaCO3.
如果电线表面清洁度和亮度是一个关键因素,建议使用去离子水制备溶液并随后加满。水的推荐硬度为 150ppm CaCO3。
- Operating temperature should be in the range of 30 – 40 °C for best results.
为获得效果,工作温度应在 30 - 40 ℃ 范围内。
- INSDRAW LS11 mixes with water to form a solution not an emulsion like typical semi-synthetics. Mixing is much easier or reduce the chance of mixing problems during makeup .
INSDRAW LS11 与水混合形成溶液,而不是典型的半合成乳液。充分混合更方便使用或减少混合形成问题的概率。
RECOMMENDED SOLUTION CONCENTIONS使用浓度推荐
Finishing精加工 0.03 - 0.08mm 10 - 15%
Finishing精加工 0.08 - 0.15mm 15 - 20%
Finishing精加工 0.15 - 0.30mm 20 - 35%
PACK SIZES 包装
INSDRAW LS11 is filled in 200kg steel drums.
INSDRAW LS11 包装为 200kg 铁桶.
TECHNICAL DATA 典型数据
PROPERTY项目 | TEST METHOD 测试方法 | RESULT结果 |
Concentrate appearance 原液外观 | MWF TM 01 | Yellowish white transparent liquid 淡黄白色透明液体 |
Emulsion pH (15% in de-ionized water) 稀释液 pH 值(15% 去离子水) | MWF TM 05 | 9.1 |
Conductivity at 25°C (15% in de ionized water), μS/cm 电导率 25。C (15%去离子水), μS/cm | MWF TM36 | 706.6 |
Density at 20°C, g/cm3 密度 20℃, g/cm3 | MWF TM 04 | 1.0547 |
CONCENTRATION MONITORING浓度监控
Emulsion concentration is generally measured using a refractometer measuring on the Brix scale.
工作液浓度通常使用手持式折光仪确定。
To obtain the actual concentration multiply the refractometer reading by the correction factor 1.83
要获得实际浓度,将折光仪读数乘以折光系数 1.83
e.g., Refractometer reading折光仪读数 = 1.5
Correction factor折光系数 1.83
Read actual concentration 实际浓度 = 2.75%
STORAGE 储存
Keep drums protected from direct sunlight and frost. Storage temperature should be controlled to
between 5°C and 35°C.
避免桶受阳光直射和霜冻。储存温度应控制在 5℃至 35℃之间。