技术指标
Technical Index
测试方法
Test Method
拉伸测试 Tensile Test
(23°C, 50% RH)
纵向
MD
横向
TD
纵向
MD
横向
TD
/
拉伸强度 Tensile
Strength(MPa)
45 38 40 35 30 ASTM D 882
弹性模量 Tensile
Modulu(MPa)
480 400 400 350 400 ASTM D 882
断裂伸长率
Elongation at
break(%)
175 150 190 170 150/180 ASTM D 882
比重 Specific Gravity 1.97 1.97 1.98 —
其它性能
Other properties
技术指标
Technical Index
测试方法
Test Method
电导率 2
Conductivity(S/cm)
0.095 0.134 0.100
20042.3-2009
氢气透过率
3Hydrogen
Crossover(ml/min·cm
2)
<0.010 <0.010 <0.015/0.010
20042.3-2009
透氢电流密度 4
Hydrogen Crossover
Current(mA/cm2)
<2.0 <2.0 / 科润 THINKE
水解性能
Hydrolytic Properties
技术指标
Index Parameters
测试方法
Test Method
含水量 5
Water Content(%)
10.0±3.0 10.0±3.0 5.0±3.0 ASTM D570
WWW.THINKRE.CN
吸水率 6
Water Uptake(%)
50.0±5.0 50.0±5.0 50.0±5.0 ASTM D570
厚度溶胀率
Thickness Change
从23°C, 50% RH到 23°C 浸泡
from 50% RH, 23°C to water soaked,23°C
10 15 10
ASTM D756
厚度溶胀率
Thickness Change
从 23°C, 50% RH 到 100°C 浸
泡
from 50% RH, 23°C to water soaked,100°C
30 40 30 ASTM D756
纵向
MD
横向
TD
纵向
MD
横向
TD
/
线性溶胀率
Linear expansion
从23°C, 50% RH到 23°C 浸泡
from 50% RH, 23°C to water soaked,23°C
3 4 3 5 4 ASTM D756
线性溶胀率
Linear expansion
从23°C, 50% RH到 23°C 浸泡
from 50% RH, 23°C to water soaked,100°C
5 2 10 5 20 ASTM D756
1膜测试前在 23°C, 50% RH 环境下至少放置 24h。
Measurements taken with membrane conditioned to 23°C, 50% RH. 2电导率测试是 23°C, 100 RH 下进行。
Conductivity measurements a 23 °C, 100 RH. 3氢气透过率测试是在 23°C, 100RH 下进行的。
Hydrogen crossover measured at 23 °C, 100 RH. 4透氢电流测试:将膜组装做成 MEA,在 80°C 氢气完全水和状态下进行的。
Hydrogen crossover Current measured in MEA on H2, 80°C, fully humidified gases. 5膜在 23°C, 50% RH 环境下相对于干膜的含水量。
Water content of membrane conditioned to 23 °C and 50% RH (dry weight basis). 6膜在 100°C, 水煮 1h 后相对于干膜的吸水率。