瑞昌明盛进出口贸易有限公司长期供应PLC、DCS系统备件 模块
【主营产品】:
Allen-Bradley(美国AB)系列产品》
ABB(ABB)系列产品》
Invensys Foxboro(福克斯波罗)
Schneider(施耐德电气)系列产品》
General electric(通用电气)系列产品》
Westinghouse(美国西屋)系列产品》
SIEMENS(西门子系列产品)》
销售ABB Robots. FANUC Robots、YASKAWA Robots、KUKA Robots、
Mitsubishi Robots、OTC Robots、Panasonic Robots、MOTOMAN
Robots。
Westinghouse(西屋): OVATION系统、WDPF系统、MAX1000系统备件。
Invensys Foxboro(福克斯波罗):I/A Series系统,FBM(现场输入/输出模块)
顺序控制、梯形 逻辑控制、事故追忆处理、数模转换、输入/输出信号处理、数据通信及处理等。
Invensys Triconex: 冗余容错控制系统、基于三重模件冗余(TMR)结构的zui现代化的容错控制器。
Siemens(西门子):Siemens MOORE, Siemens Simatic C1,Siemens数控系统等。
Bosch Rexroth(博世力士乐):Indramat,I/O模块,PLC控制器,驱动模块等。
Motorola(摩托罗拉):MVME 162、MVME 167、MVME1772、MVME177等系列。
尊敬的顾客您好,为了更好的保障您的合法权益,购买前请仔细阅读以下内容:
1.价格说明 并非原价,请以询价为准!
价格说明 并非原价,请以询价为准!
价格说明 并非原价,请以询价为准!
2.由于市场波动频繁,本店所标价格,并非实价,请买家提前 咨询 后再拍,感谢支持。
3.所售商品报价均为不含税价 ,如须开票,请和店主联系。
4.本店所售商品均为正品现货,图片实物拍摄。如果您订购产 品超过 多件,请与我们联系,我们可以为您尽量提供折扣。
5.本店产品分为全新原装、全新无包装,工程余货和二手四种 货品。购买前请联系客服仔细核对货品、型号、数量。
6.本店所售商品***质量,全新无包装和二手商品签收十五日 出现问题均包退换,请放心购买。所有配件质保一年。因 买家自己弄错产品型号、参数或剪脚、上机、错误接入电 源、错误安装、保管不当、人为损坏等除外。
7.本店所售商品国内顺丰包邮,国外运费自理。支持十五天内 有任何产品质量问题退换货,过期一切损失请自行承担。请 大家在货物签收时一定仔细检查物品外观是否完好无损,数 量是否短缺,配件是否齐全如发现有任何问题请不要签收并 立即致电我们,货物一旦签收完毕,就代表双方对货物外 表、数量、配件一致认可无争议。
拍下商品后,视为认可以上各项条款,谢谢合作!
Soft starter can be set as soft start, soft stop, current limiting start and intelligent braking. Soft starter is especially suitable for the start and stop control of large capacity motor. It is an intelligent product. Soft start and soft stop of motor is a new starting mode. Soft start means that the input voltage of the motor starts from 0V and increases gradually according to the preset mode until the end of full voltage. The soft stop of the motor is that the motor starts from the rated speed and decelerates gradually according to the preset way until it stops. Soft start and soft stop depend on the power supply connected in series
The soft starter is used to control the conduction angle of the thyristor in the soft starter, so as to control its output voltage or current, so as to effectively control the start and stop of the motor. The connection of Rockwell's smcplus soft starter standard unit in the main circuit is shown in Figure 1. In the figure, the normally open contacts of the parallel contactor kmnl (n = 1,2,3,4, the same below) are at the input and output ends of the soft starter, and the normally open contacts of the series contactor km and the contactor kmn2 are at the input and output ends of the soft starter. When soft starting, contact km and contact kmn2 are closed, contact kmn1 is open, and starting current flows to motor through soft starter. After the soft start, the contact kmn1 is closed, the contact km and the contact kmn2 are disconnected, the soft starter does not work, and the working current is sent to the motor through kmn1. When soft stop occurs, contact km and contact kmn2 are closed, and contact kmn1 is opened to realize soft stop until the motor stops running, and then contact km and contact kmn2 are opened. This method greatly improves the service life of the soft starter and avoids the high-order harmonic generated by the soft starter when the motor is running. Because when the contactor is on or off, the voltage at both ends of the contact is basically zero, which also improves the service life of the contactor.