NORYL GFN1720 20%玻璃纤维增强

¥56.00 ≥25千克起批

参数

否是否进口
中国厂家(产地)
GFN1720 牌号

发货地广东东莞不限

东莞市聚浩塑化有限公司 3年: 进入店铺在线咨询

NORYL GFN1F 10%玻璃纤维增强 ¥56.00

NORYL GFN2 20%玻璃纤维增强 ¥56.00

NORYL GFN20 PPE+PS混合物。20%玻璃纤维增强 ¥56.00

NORYL GFN2RC3 高强度、水解稳定性、低翘曲、低比重和尺寸稳定性 ¥43.00

NORYL GFN3 30%玻璃增强。低吸水性 ¥43.00

NORYL GFN30 30%玻璃增强 ¥43.00

产品详情

PROPERTIES		TYPICAL VALUES	UNITS	TEST METHODS
FLAME CHARACTERISTICS	1)
UL Yellow Card Link		E45329-236755	-	-
UL Recognized, 94HB Flame Class Rating		≥1.5	mm	UL 94
Glow Wire Flammability Index 960°C, passes at	4)	3.2	mm	IEC 60695-2-12
Oxygen Index (LOI)		23	%	*** 4589
MECHANICAL	2)
Tensile Stress, yld, Type I, 5 mm/min		90	MPa	ASTM D638
Tensile Stress, brk, Type I, 5 mm/min		90	MPa	ASTM D638
Tensile Strain, yld, Type I, 5 mm/min		2.5	%	ASTM D638
Tensile Strain, brk, Type I, 5 mm/min		3	%	ASTM D638
Tensile Modulus, 5 mm/min		5500	MPa	ASTM D638
Flexural Stress, yld, 1.3 mm/min, 50 mm span		145	MPa	ASTM D790
Flexural Modulus, 1.3 mm/min, 50 mm span		4800	MPa	ASTM D790
Taber Abrasion, CS-17, 1 kg		45	mg/1000cy	SABIC method
Tensile Stress, yield, 5 mm/min		90	MPa	*** 527
Tensile Stress, break, 5 mm/min		90	MPa	*** 527
Tensile Strain, yield, 5 mm/min		2	%	*** 527
Tensile Strain, break, 5 mm/min		2	%	*** 527
Tensile Modulus, 1 mm/min		6000	MPa	*** 527
Flexural Stress, break, 2 mm/min		135	MPa	*** 178
Flexural Modulus, 2 mm/min		4500	MPa	*** 178
Ball Indentation Hardness, H358/30		100	MPa	*** 2039-1
IMPACT	2)
Izod Impact, notched, 23°C		60	J/m	ASTM D256
Izod Impact, notched, -30°C		50	J/m	ASTM D256
Instrumented Dart Impact Total Energy, 23°C		14	J	ASTM D3763
Izod Impact, unnotched 80104 +23°C		25	kJ/m²	*** 180/1U
Izod Impact, unnotched 80104 -30°C		25	kJ/m²	*** 180/1U
Charpy 23°C, Unnotch Edgew 80104 sp=62mm		25	kJ/m²	*** 179/1eU
Charpy -30°C, Unnotch Edgew 80104 sp=62mm		25	kJ/m²	*** 179/1eU
THERMAL	2)
Vicat Softening Temp, Rate B/50		181	°C	ASTM D1525
CTE, -40°C to 40°C, flow		4.E-05	1/°C	ASTM E831
CTE, -40°C to 40°C, xflow		5.E-05	1/°C	ASTM E831
Thermal Conductivity		0.26	W/m-°C	*** 8302
CTE, 23°C to 80°C, flow		3.E-05	1/°C	*** 11359-2
CTE, 23°C to 80°C, xflow		7.E-05	1/°C	*** 11359-2
Ball Pressure Test, 125°C +/- 2°C		PASSES	-	IEC 60695-10-2
Ball Pressure Test, approximate maximum		165	°C	IEC 60695-10-2
Vicat Softening Temp, Rate A/50		180	°C	*** 306
Vicat Softening Temp, Rate B/50		170	°C	*** 306
Vicat Softening Temp, Rate B/120		180	°C	*** 306
HDT/Be, 0.45MPa Edgew 120104 sp=100mm		170	°C	*** 75/Be
HDT/Ae, 1.8 MPa Edgew 120104 sp=100mm		160	°C	*** 75/Ae
Relative Temp Index, Elec	1)	65	°C	UL 746B
Relative Temp Index, Mech w/impact	1)	65	°C	UL 746B
Relative Temp Index, Mech w/o impact	1)	65	°C	UL 746B
PHYSICAL	2)
Specific Gravity		1.24	-	ASTM D792
Mold Shrinkage on Tensile Bar, flow	5)	0.2-0.4	%	SABIC method
Mold Shrinkage, flow, 3.2 mm	5)	0.2-0.4	%	SABIC method
Melt Flow Rate, 300°C/5.0 kgf		4.5	g/10 min	ASTM D1238
Density		1.24	g/cm³	*** 1183
Water Absorption, (23°C/saturated)		0.15	%	*** 62-1
Moisture Absorption (23°C / 50% RH)		0.06	%	*** 62
Melt Volume Rate, MVR at 300°C/10.0 kg		11	cm³/10 min	*** 1133
ELECTRICAL	2)
Volume Resistivity		1.E+15	Ω.cm	IEC 60093
Surface Resistivity, ROA		>1.E+15	Ω	IEC 60093
Dielectric Strength, in oil, 0.8 mm		30	kV/mm	IEC 60243-1
Dielectric Strength, in oil, 1.6 mm		26	kV/mm	IEC 60243-1
Dielectric Strength, in oil, 3.2 mm		16	kV/mm	IEC 60243-1
Relative Permittivity, 1 MHz		2.6	-	IEC 60250
Dissipation Factor, 50/60 Hz		0.006	-	IEC 60250
Dissipation Factor, 1 MHz		0.002	-	IEC 60250
Comparative Tracking Index	4)	200	V	IEC 60112
Relative Permittivity, 50/60 Hz		2.7	-	IEC 60250
INJECTION MOLDING	3)
Drying Temperature		110-120	°C
Drying Time		2-4	Hrs
Melt Temperature		290-330	°C
Nozzle Temperature		290-310	°C
Front - Zone 3 Temperature		310-330	°C
Middle - Zone 2 Temperature		290-310	°C
Rear - Zone 1 Temperature		270-290	°C
Hopper Temperature		60-80	°C
Mold Temperature		80-120	°C

为您推荐

NORYL GFN30F 低吸水性水解稳定性 ¥43.00
NORYL GFN30F PPE（聚苯醚）+PS（聚苯乙烯）共混物。30%玻璃纤维增强 ¥56.00
SABIC Noryl GFN3F 水解稳定性。尺寸稳定性。适用于流体工程应用 ¥56.00
SABIC Noryl GNF3 3 0%玻璃纤维增强。低吸水性。水解稳定性 ¥39.00
SABIC Noryl GFN3V ¥39.00
SABIC Noryl HF185 阻燃且流动性好 ¥56.00

SABIC Noryl HM3020H PPE+PS GF+MF 30%填充，FR V-1，高流量 ¥56.00
SABIC Valox HM4025H PPE/PS混合物，高流动性 ¥56.00
SABIC Noryl HN731SE 用于医疗器械和制药应用 ¥56.00
SABIC Noryl HNA033 未填充的改性聚苯醚树脂 ¥56.00
SABIC Noryl HNA055 ¥56.00
SABIC Noryl HNA055 个人防护装备 ¥67.00

SABIC Noryl HS2000X 矿物增强17%。无溴、无氯阻燃体系 ¥67.00
SABIC Noryl IGN320 用于高温、高模量的汽车应用 ¥56.00
SABIC Noryl INT2001 汽车内饰用 ¥67.00
SABIC Noryl INT2001 汽车内饰用未填充的PPE ¥56.00
NORYL LEN2211 高抗冲 ¥67.00
SABIC NORYL LS6010 阻燃 ¥67.00

供应商网> 特种塑料> NORYL GFN1720 20%玻璃纤维增强

在线问

产品参数

是否进口否
厂家(产地)中国
牌号GFN1720
用途级别注塑

1/2

¥56.00 在线咨询

进店客服获取最低报价拨打电话

NORYL GFN1720 20%玻璃纤维增强: ¥56.00