应用
控制和调节过程值
监控设备并控制电路通断
适用于过压较高的测量点
监测过滤器和泵
密封罐内的液位测量
功能特性
差压测量范围:0 … 1.6 kPa
高工作压力(静压),过压安全保护高达4 MPa
可提供可充液外壳,适用于高动态压力负载和高振动环境
提供带感应式电接点的仪表,用于危险区域
提供带开关电接点的仪表,适合PLC应用
描述
无论何种情况下,如果您希望在本地显示过程压力的同时,对电路进行通断操作,switchGAUGE系列的DPGS43.1x0型压力表将是理想选择。
开关电接点(报警用电子式电接点)可根据仪表的指针位置接通和关断电气控制电路。开关电接点在全量程范围内可调(参见DIN 16085)。通常情况下,电接点都安装在表盘下面,只有少数是安装在表盘上面。仪表指针(实际值指针)可在整个量程范围内自由旋转,与设定无关。
设定指针可以通过窗口内的可拆卸调整键进行调整。
开关电接点不仅包含多个电接点,而且可以设置单个设定值。当实际值指针超过或低于设定值时,电接点便会进行切换。
该型号压力表根据DIN 16085标准制造,并且符合所有相关标准(如EN 837-3)和规范的安全要求,完全可用于现场测量高压容器的工作压力。
开关电接点包括磁助式电接点、干簧电阻链式电接点、感应式电接点和电子式电接点。其中感应式电接点可应用与危险区域。电子式和干簧电阻链式电接点可用于用于触发PLC。
Models DPGS43.100, DPGS43.160 Version Process connections lower mount or lateral (option), highly corrosion-resistant solid metal design, measuring cell protected against unauthorised access. Overload resistance per EN 837-3 Nominal size in mm ■ 100 ■ 160 Accuracy class 1.6 Option: 1.0 on request Scale ranges 0 ... 16 mbar to 0 ... 250 mbar 0 ... 400 mbar to 0 ... 40 bar other units (e.g. psi, kPa) available or all other equivalent vacuum or combined pressure and vacuum ranges Scale Single scale Option: ■ Dual scale ■ Scale layout (e.g. linear pressure or square root incrementation) Zero point setting Without Option: Zero point adjustment appliance Pressure limitation Steady Full scale value Fluctuating 0.9 x full scale value Observe the recommendations for the use of mechanical pressure measuring systems in accordance with EN 837-2 Overpressure safety and max. working pressure (static pressure) see table on page 3 Connection location Lower mount (radial) Option: lateral (right, left, front or back) Process connection ■ G ¼ B female ■ G ½ B male ■ ½ NPT male Other process connections via female or male threads on request Restrictor Without Option: Restrictor in the pressure port Permissible temperature 1) Medium -20 ... +100 °C Option: Medium temperature > 100 °C on request Ambient -20 ... +60 °C (with window from polycarbonate max. 80 °C) Temperature effect When the temperature of the measuring system deviates from the reference temperature (+20 °C): max. ±0.5 %/10 K of full scale value Case ■ Version S1 per EN 837: With blow-out device in case back ■ Safety version S3 per EN 837: With solid baffle wall (Solidfront) and blow-out back Case filling Without Option: With case filling Venting of the media chamber With scale ranges ≤ 0.25 bar Option: With scale ranges ≥ 0.4 bar 1) For hazardous areas, the permissible temperature of the contact model 831 will exclusively apply (see page 5). These must not be exceeded at the instrument either (for details see operating instructions). If necessary, measures for cooling (e.g. syphon, instrumentation valve, etc.) have to be taken. WIKA data sheet PV 27.05 ∙ 06/2021 Page 3 of 14 Scale ranges Overload safety in bar either side max. Max. working pressure in bar (static pressure) Standard Option Standard Option 0 ... 16 to 0 ... 40 mbar 2.5 - 2.5 6 2) 0 ... 60 to 0 ... 250 mbar 2.5 6 6 10 0 ... 400 mbar 4 40 25 40 0 ... 0.6 bar 6 40 25 40 0 ... 1 bar 10 40 25 40 0 ... 1.6 bar 16 40 25 40 0 ... 2.5 to 0 ... 25 bar 25 40 25 40 2) Accuracy class 2.5 Overload safety and max. working pressure Models DPGS43.100, DPGS43.160 Wetted materials Media chamber with process connection Stainless steel 316Ti (1.4571) Lower mount 2 x G ¼ female Pressure elements ≤ 0.25 bar: Stainless steel 316L > 0.25 bar: NiCr alloy (Inconel) Venting of the media chamber Stainless steel 316Ti (1.4571) for scale ranges ≤ 0.25 bar Option: with scale ranges ≥ 0.4 bar Bellows Stainless steel 316Ti (1.4571) Non-wetted materials Movement Brass Dial Aluminium, white, black lettering Pointer Aluminium, black Case Stainless steel, with blow-out device Window Laminated safety glass Ring Bayonet ring, stainless steel Ingress protection per IEC/EN 60529 IP54 1 ) Option: IP65 with liquid filling Installation according to affixed symbols: ⊕ high pressure, ⊖ low pressure Mounting ■ Rigid measuring lines ■ Mounting holes in measuring flange Option: ■ Panel mounting flange ■ Instrument mounting bracket for wall or pipe mounting Electrical connection Cable socket PA 6, black Per VDE 0110 insulation group C/250 V Cable gland M20 x 1.5 Strain relief 6 screw terminals + PE for conductor cross-section 2.5 mm² For dimensions see page 10 others on request 1) Ingress protection IP54 with safety version and lower back mount. WIKA data sheet PV 27.05 ∙ 06/2021 Page 4 of 14 Switch contacts Magnetic snap-action contact model 821 ■ No control unit and no supply voltage required ■ Direct switching up to 250 V, 1 A ■ Up to 4 switch contacts per measuring instrument Inductive contact model 831 ■ Suitable for use in hazardous areas with corresponding control unit (model 904.xx) ■ Long service life due to non-contact sensor ■ Low influence on the indication accuracy ■ Fail-safe switching at high switching frequency ■ Insensitive to corrosion ■ Also available in safety version ■ Up to 3 switch contacts per measuring instrument Electronic contact model 830 E ■ For direct triggering of a programmable logic controller (PLC) ■ 2-wire system (option: 3-wire system) ■ Long service life due to non-contact sensor ■ Low influence on the indication accuracy ■ Fail-safe switching at high switching frequency ■ Insensitive to corrosion ■ Up to 3 switch contacts per measuring instrument Other versions ■ Contact model 821 with separate circuits ■ Contact model 821 as change-over contact (break or make simultaneously at the set point) ■ Contact model 821 with cable break monitoring (parallel resistance 47 kΩ and 100 kΩ) ■ Contact materials for contact model 821: Platinum-iridium alloy and gold-silver alloy ■ Contacts fixed, without contact adjustment lock ■ Contact adjustment lock leaded ■ Contact adjustment key fixed ■ Connector (instead of cable socket) Reed switch model 851 ■ No control unit and no supply voltage required ■ Direct switching up to 250 V, 1 A ■ For direct triggering of a programmable logic controller (PLC) ■ Free from wear as without contact ■ NS 100: Up to two change-over contacts per measuring instrument; NS 160: Up to one change-over contact per measuring instrument (switching voltages AC<50 V and DC <75 V, switch contact not adjustable from outside) Switching function The switching function of the switch is indicated by index 1, 2 or 3 Model 8xx.1: Normally open (clockwise pointer motion) Model 8xx.2: Normally closed (clockwise pointer motion) Models 821.3 and 851.3: Change-over; one contact breaks and one contact makes simultaneously when pointer reaches set point For further information on switch contacts, see data sheet AC 08.01