注:本手册中出现的重要安全注意事项和说明并非涵盖所有内容
可能出现的条件和情况。必须理解,常识和谨慎是:
本风机安装和运行中的必要因素。
注:本产品不适用于身体、感官或生理机能减退的人(包括儿童)
心智能力不同或受损,或缺乏经验或知识,除非这些人:
由负责其安全的人员监督或培训操作设备。
注意:应监督儿童,确保他们不将电器用作玩具。
警告:关闭保险丝或断路器处的电源
请检查以上附件是否齐全?是的,然后安装。
将风扇连接到电气箱
操作您的风扇
打开电源并检查风扇的运行情况。风扇拉链控制风扇速度如下:1拉高,2拉中,3拉低,4拉离。
用于温暖或凉爽天气的适当速度设置取决于诸如房间大小、天花板高度等因素,
以及风扇的数量。滑动开关(XX)控制刀片的方向:前进(向下切换)或后退
(接通电源)。
A–温暖天气-(前进)向下气流产生冷却效果。这可以让你调整你的空气
在不影响舒适度的情况下,将护发素设置在更高的位置。
B–凉爽天气-(反向)向上气流将热空气从天花板上移开。这允许您设置反向
加热装置的设置较低,不会影响您的舒适度。
安装和操作说明01
将风扇连接到电气箱01
将风扇连接到电气箱02
将风扇连接到电气箱03
将风扇连接到电气箱04
将风扇连接到电气箱05
运行风扇01
运行风扇02
使用风扇附带的电线连接螺母
风扇必须保持高速
遥控器
一般资料
此遥控器设计用于单独控制吊扇速度和灯光的打开和关闭
控制风扇速度和关闭的按钮(高、中、低、关)。
灯光按钮将控制灯光的打开和关闭。
按下五个按钮之一时,变送器上的红色指示灯将点亮。
安装和操作说明
1.设置代码
要设置代码,请执行以下步骤:
设置变送器上的代码:
拆下电池盖。用力按箭头并将电池盖滑出。
滑码切换到您选择的向上或向下位置。(出厂设置已全部设置。请勿使用此选项
位置使用小螺丝刀或圆珠笔上下滑动)。
在接收器上设置代码:
按下电源按钮后,必须在30秒钟内按下学习键。
如果没有,请按电源按钮重新启动。
持续按下按钮“学习”键超过3秒,将变为学习状态。
接收器可以记住***的代码状态。灯闪烁两次。
2.在吊扇中安装接收器
安全注意事项:
警告:高压!通过拆下保险丝或关闭断路器来断开电源。
请勿与固态风扇一起使用。
电线必须符合所有地方和国家电气规范要求。
风扇电源必须为110/120伏,60Hz。风扇电机电流:1.0,光功率:180
白炽灯或镇流器和LED。
否则,电源可能导致严重伤害或死亡。
在风扇中安装接收器:
断开电路的电源NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense and caution are necessary factors in the installation and operation of this fan. NOTE: This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities are different or are impaired, or lack of experience or knowledge, unless such persons are supervised or trained to operate the appliance by a person responsible for their safety. NOTE: Children should be supervised to ensure that they do not use appliances as a toy. WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER Please check whether above accessories are completed or not? Yes, and install. Attaching the Fan to the Electrical Box OPERATING YOUR FAN Turn on the power and check the operation of the fan. The fan pull chain controls the fan speed as follows: 1 pullHigh,2 pulls-Medium,3 pulls-Low,4 pulls-off. The appropriate speed settings for warm or cool weather depends on factors such as the room size,ceiling height, and number of fans. The slide switch (XX) controls the direction of the blades: forward (switch down) or reverse (switch up). A – Warm weather-(Forward) A Downward airflow creates a cooling effect. This allows you to set your air conditioner on a higher setting without affecting your comfort. B – Cool weather-(Reverse) An upward airflow moves warm air off the ceiling. This allows Reverse you to set heating unit on a lower setting without affecting your comfort. Installation & Operating Instructions 01 Attaching the Fan to Electrical Box 01 Attaching the Fan to Electrical Box 02 Attaching the Fan to Electrical Box 03 Attaching the Fan to Electrical Box 04 Attaching the Fan to Electrical Box 05 Operating Fan 01 Operating Fan 02 Use wire connecting nuts supplied with the fan FAN MUST BE KEPT AT THE HIGH SPEED Remote Controller GENERAL INFORMATION This remote controller is designed to separately control your ceiling fan speed and light on and off. There are four buttons(HI, MED, LOW, OFF) to control the speed of the fan and off. The light button will control the light on and off. The red indicator on the transmitter will light when one of the five buttons is pressed. INSTRUCTION OF INSTALLATIONAND OPERATION 1. SETTING THE CODES To set the codes, perform the following steps: Setting the codes on the transmitter: Remove battery cover. Press firmly on the arrow and slide battery cover off. Slide code switches to your choice of up or down position. (Factory setting is all up. Do not use this position. Use a Small screwdriver or ball point pen to slide firmly up or down). Setting the codes on the receiver: The Learn Key must be pressed with in 30 seconds, after pressing the Power button. If not, please press the Power button to restart. Keep pressing the button learn key in excess of 3 second it becomes a LEARN status. The receiver can remember the last codes status. The light flash two times. 2. INSTALLING RECEIVER IN CEILING FAN Safety precautions: WARNING: HIGH VOLTAGE! Disconnect power by removing fuse or switching off circuit breaker. Do not use with solid state fans. Electrical wire must meet all local and national electrical code requirements. Supply for fan must be 110/120 volt, 60Hz. Maximum fan motor amps: 1.0, Maximum light watts: 180 incandescent or ballast and LED. Otherwise power can cause serious injury or death. Installing receiver in fan: Remove power from the circui