取消

厂家库存工厂库存出口库存义乌库存低价库存品牌库存库存处理库存产品库存货源库存清仓

商品
详情

350015控继电模块PLC库存

¥7612.00 1 - 99
¥6973.00 ≥100

参数

卡件模块产品特性
否是否进口
美国产地

发货地江西瑞昌市 1天内发货供货总量211个

瑞昌明盛自动化设备有限公司 4年: 进入店铺在线咨询

350020工控继电模块PLC库存 ¥6973.00

350022工控继电模块PLC库存 ¥6973.00

3500/25工控继电模块PLC库存 ¥6973.00

350032工控继电模块PLC库存 ¥6973.00

350033工控继电模块PLC库存 ¥6973.00

350040工控继电模块PLC库存 ¥6973.00

产品详情

产品介绍Product introduction

在操作、维护和维修的所有阶段，必须遵守以下一般安全预防措施

这个设备。未遵守这些预防措施或本手册其他地方的具体警告

可能导致人身伤害或设备损坏。

下面列出的安全预防措施代表了摩托罗拉意识到的某些危险的警告。你，作为

产品使用者应遵守这些警告以及安全所需的所有其他安全预防措施

设备在您的操作环境中的操作。

把仪器接地。

为了尽量减少电击危险，设备机箱和外壳必须连接到电气接地。如果

设备配有三芯交流电源电缆，电源电缆必须插入经批准的

三触点插座，接地线（绿色/黄色）可靠地连接到电气接地

（安全接地）在电源插座处。电力电缆的电源插座和配套插头符合***

电工委员会（IEC）安全标准和当地电气监管规范。

请勿在爆炸性环境中操作。

请勿在任何爆炸性环境中操作设备，如存在易燃气体或烟雾。

在这种环境中操作任何电气设备都可能导致爆炸并造成伤害，或

损坏

远离设备内部的带电电路。

操作人员不得拆除设备盖。只有工厂授权的服务人员或其他

合格的维修人员可拆除设备盖以更换内部组件或部件

或任何内部调整。维修人员不应更换已连接电源电缆的部件。在下面

在某些情况下，即使移除了电源电缆，也可能存在危险电压。为了避免受伤，例如

在接触部件之前，人员应始终断开电源和放电电路。

暴露或处理CRT时要小心。

阴极射线管（CRT）的破裂导致玻璃碎片的高速散射（内爆）。到

防止阴极射线管内爆，不要处理阴极射线管，避免粗暴处理或设备震动。处理

CRT只能由合格的维修人员使用经批准的安全面罩和手套进行。

不要更换零件或修改设备。

不得安装替代零件或对设备进行任何未经授权的修改。联系当地人

摩托罗拉服务和维修代表，确保维护所有安全功能。

遵守手册中的警告。

在本手册中，潜在危险程序之前会出现警告，如以下示例。

必须遵守警告中包含的说明。您还应采取所有其他安全预防措施

您认为在您的操作环境中操作设备是必要的。

警告

警告：为了防止危险电压造成严重伤害或死亡，请使用极限电压

搬运、测试和调整本设备及其

The following general safety precautions must be observed during all phases of operation, service, and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment. The safety precautions listed below represent warnings of certain dangers of which Motorola is aware. You, as the user of the product, should follow these warnings and all other safety precautions necessary for the safe operation of the equipment in your operating environment. Ground the Instrument. To minimize shock hazard, the equipment chassis and enclosure must be connected to an electrical ground. If the equipment is supplied with a three-conductor AC power cable, the power cable must be plugged into an approved three-contact electrical outlet, with the grounding wire (green/yellow) reliably connected to an electrical ground (safety ground) at the power outlet. The power jack and mating plug of the power cable meet International Electrotechnical Commission (IEC) safety standards and local electrical regulatory codes. Do Not Operate in an Explosive Atmosphere. Do not operate the equipment in any explosive atmosphere such as in the presence of flammable gases or fumes. Operation of any electrical equipment in such an environment could result in an explosion and cause injury or damage. Keep Away From Live Circuits Inside the Equipment. Operating personnel must not remove equipment covers. Only Factory Authorized Service Personnel or other qualified service personnel may remove equipment covers for internal subassembly or component replacement or any internal adjustment. Service personnel should not replace components with power cable connected. Under certain conditions, dangerous voltages may exist even with the power cable removed. To avoid injuries, such personnel should always disconnect power and discharge circuits before touching components. Use Caution When Exposing or Handling a CRT. Breakage of a Cathode-Ray Tube (CRT) causes a high-velocity scattering of glass fragments (implosion). To prevent CRT implosion, do not handle the CRT and avoid rough handling or jarring of the equipment. Handling of a CRT should be done only by qualified service personnel using approved safety mask and gloves. Do Not Substitute Parts or Modify Equipment. Do not install substitute parts or perform any unauthorized modification of the equipment. Contact your local Motorola representative for service and repair to ensure that all safety features are maintained. Observe Warnings in Manual. Warnings, such as the example below, precede potentially dangerous procedures throughout this manual. Instructions contained in the warnings must be followed. You should also employ all other safety precautions which you deem necessary for the operation of the equipment in your operating environment. Warning Warning To prevent serious injury or death from dangerous voltages, use extreme caution when handling, testing, and adjusting this equipment and its

产品信息