ACG10S-F2113 S4
常见的规格
l安装环境
项规范
环境温度
正常操作
0 ~ 50°C (AFV30,AFV40,ACB51, AFV10)
0 ~ 60°C (ANB10,ANB11,ANT10U, ANR10,I/O模块,
通信模块和总线接口模块)
(-20 ~ 70℃温度可选:ANB10,ANB11,ANT10U, ANR10,
I/O模块,通信模块和总线接口模块)(*1)
运输/储存
-20 ~ 60℃(避免阳光直射)
(-40至85°C温度可选:ANB10,ANB11,ANT10U, ANR10,
避免使用I/O模块、通信模块和总线接口模块
阳光直射)
环境湿度正常工作5% ~ 95% RH(无凝露现象)。
运输/储存5%至95% RH(应无冷凝)。
环境温度
变化率
正常工作±10℃/h
运输/储存:±20°C/h
电力供应
电压范围
100 ~ 120v AC±10%
220 ~ 240v AC±10%
24v dc±10%
频率50/60±3hz
失真系数不超过10%
峰值125v及以上(100v系统)
274v及以上(220v系统)
瞬时功率
故障≤20ms(接收额定交流电压时)
直流电源纹波
税率1% p-p或***
接地不超过100欧姆,独立接地
粉尘0.3 mg/m3
或更少
腐蚀性气体ANSI/ISA S71.04 G2(标准)(ANSI/ISA S71.04 G3选配)
振动
连续振动位移幅值≤0.25 mm (1 ~ 14hz)
加速度2.0 m/s2
或***(14至100赫兹)
地震加速度4.9 m/s2
或更少
输送振动水平4.9 m/s2
或者更小,垂直9.8米/s2
或更少(填充状态)
激波输送激波水平49.0 m/s2
,垂直98.0 m/s2
(包装状态)
噪音
电场
≤3v /m (26mhz ~ 1.0 GHz)
≤3v /m (1.4 ~ 2.0 GHz)
1v /m以下(2.0 ~ 2.7 GHz)
磁场≤30a /m(交流),≤400a /m(直流)
静电4kv或以下(接触放电),8kv或以下(架空放电)
海拔2000米以下
*1: ER总线节点单元在温度环境(-20℃~ 0℃)下使用时,启动时间为10分钟
EB501打开电源开关后。
当在ESB总线节点单元、光ESB总线节点单元或ER总线节点单元中安装了以下模块时
环境温度应控制在0 ~ 50℃。
Aap149, aap849, adv157, adv557, adv161, adv561, adv859, adv159, adv559, adv869, adv169, adv569,
Alr111, alf111, alp111, alp121
当AAI543-6、-F(快速响应)安装在ESB总线节点单元、光ESB总线节点单元或ER总线节点时
一般情况下,环境温度应在0 ~ 60℃
l ESB bus/Optical ESB bus
When using Field Control Unit (AFV30/AFV40)
Application
An ESB bus or an optical ESB bus is an input/output communication bus that connects the ESB bus node unit or
optical ESB bus node unit to the intelligent part of the FCS.
Communication Specifications
Connectable Units: ESB Bus Node Unit (ANB10), Optical ESB Bus Node Unit (ANB11), and Unit for Optical ESB
Bus Repeater Module (ANT10U)
Number of Connectable Units: The number of ESB bus node units and optical ESB bus node units that can be
connected to the ESB bus varies depending on the selected database.
Units for Optical ESB Bus Repeater Module (ANT10U) are not included in the number of connectable units.
Field Control
Unit Database
Total Number of ESB
Bus and Optical
ESB Bus Node Units
Connected per FCU (*1)
AFV30 (*2)
AFV40 (*2) (*3)
Control Function for Field Control Station (LFS1700) Max. 3
Control Function for Field Control Station (LFS1700) plus Node Expansion Package
(LFS1750-V1) Max. 9
Control Function for Field Control Station (LFS1700) plus Node Expansion Package
(LFS1750-V2) Max. 13
*1: ESB Bus Node Unit (ANB10), Optical ESB Bus Node Unit (ANB11)
*2: To connect the ESB bus node unit and optical ESB bus node unit to the FCU (AFV30/AFV40), install the ESB Bus
Coupler Module (EC401 or EC402) in slots 7 and 8.
EC401 can be connected a maximum of nine Node Units (ANB10or ANB11).
EC402 can be connected a maximum of nine Node Units (ANB10or ANB11) on the upper and lower sides, respectively.
The sum of the total number of Node Units (ANB10 or ANB11) per FCU should not exceed the specified number.
*3: The maximum number of ESB bus node units, optical ESB bus node units, and units for optical ESB bus repeater module
that can be installed in a single cabinet is 11 for AFV40.
Transmission Path Specifications
Network Topology: Bus topology
Transmission Path Redundancy: Available
Transmission Speed: 128 megabits per second
Transmission Cable: Dedicated cable (YCB301), an optical fiber cable (*1)
Transmission Distance: Max. 10 m (*2), 50 km (when using the ANT411 Optical ESB Bus Repeater Module) (*3)
*1: Optical Fiber Cable Specifications
Connector Type: LC (compliant with IEC 61754-20)
Recommended Cable: Quartz single-mode fiber (JIS C6835 SSMA -9.3/125 IEC 60793-2-50B1.1)
Number of Cores: 2
*2: Max. 10 m for EC401 and max. 10 m on the upper and lower sides, respectively, for EC402.
*3: The distance can be extended to a maximum of 50 km using the optical ESB bus repeater module. Chain and star
connection configurations are available.
l ESB bus
When using Field Control Unit (AFV10)
Application
A input/output communication bus used in a standard FCS for FIO. The ESB bus connects the processing unit of a
FCS to local node units.
Communication Specifications
Field Control
Unit Database ESB Bus Node Units
Connected per FCU (*1)
Total Number of
ESB Bus Node Units
and ER Bus Node Units
Connected per FCU (*1)
AFV10 (*2)
Control Function for Field Control Unit (LFS1500) Max. 3 Max. 3
Control Function for Field Control Unit (LFS1500)
plus Application Capacity Expansion Package (LFS1550) Max. 9 Max. 14
*1: ESB Bus Node Units(ANB10), ER Bus Node Units(ANR10)
*2: If ESB Bus Node Units are used, install ESB Bus Coupler Module (EC401) in slot 7th and 8th.
Transmission Path Specifications
Network Topology: Bus topology
Transmission Path Redundancy: Available
Transmission Speed: 128 megabits per second
Transmission Cable: Dedicated cable (YCB301)
Transmission Distance: Max. 10 m