ULTEM 4000 聚四氟乙烯和石墨填充的标准流量聚醚酰亚胺

¥98.00 ≥25千克起批

参数

否是否进口
中国厂家(产地)
4000 牌号

发货地广东东莞不限

东莞市聚浩塑化有限公司 2年: 进入店铺在线咨询

ULTEM 4002 聚四氟乙烯填充，标准流量聚醚酰胺 ¥98.00

ULTEM 6202 12%二氧化硅填充的标准流量聚醚酰胺共聚物 ¥115.00

ULTEM 9075 高流动性聚醚酰亚胺混合物 ¥118.00

ULTEM 9085 具有低毒性、烟雾 ¥78.00

ULTEM 9090 聚醚酰亚胺混合物，延展性和耐洗涤剂性能得到改善 ¥78.00

ULTEM AR9100 10%玻璃纤维填充，标准流量聚醚酰亚胺 ¥79.00

产品详情

PROPERTIES		TYPICAL VALUES	UNITS	TEST METHODS
FLAME CHARACTERISTICS	¹⁾
UL Yellow Card Link		E121562-221109	-	-
UL Recognized, 94V-0 Flame Class Rating		0.84	mm	UL 94
Glow Wire Flammability Index 960°C, passes at	²⁾	3.2	mm	IEC 60695-2-12
Oxygen Index (LOI)		48	%	ISO 4589
MECHANICAL
Taber Abrasion, CS-17, 1 kg		30	mg/1000cy	SABIC method
PV Limit, 0.51 m/s		2.1	MPa-m/s	SABIC method
K-factor xE-10, PV=2000 psi-fpm vs Steel		50	-	SABIC method
K-factor xE-10, PV=2000 psi-fpm vs Self		1900	-	SABIC method
Tensile Stress, break, 5 mm/min		90	MPa	ISO 527
Tensile Strain, break, 5 mm/min		1	%	ISO 527
Tensile Modulus, 1 mm/min		9900	MPa	ISO 527
Flexural Stress, break, 2 mm/min		120	MPa	ISO 178
Flexural Modulus, 2 mm/min		7000	MPa	ISO 178
Ball Indentation Hardness, H358/30		140	MPa	ISO 2039-1
IMPACT
Izod Impact, unnotched 80104 +23°C		15	kJ/m²	ISO 180/1U
Izod Impact, unnotched 80104 -30°C		15	kJ/m²	ISO 180/1U
Charpy Impact, notched, 23°C		8	kJ/m²	ISO 179/2C
Charpy Impact, notched, -30°C		8	kJ/m²	ISO 179/2C
THERMAL
Thermal Conductivity		0.43	W/m-°C	ISO 8302
CTE, 23°C to 150°C, flow		1.5E-05	1/°C	ISO 11359-2
CTE, 23°C to 150°C, xflow		5.E-05	1/°C	ISO 11359-2
Ball Pressure Test, 125°C +/- 2°C		PASSES	-	IEC 60695-10-2
Vicat Softening Temp, Rate A/50		225	°C	ISO 306
Vicat Softening Temp, Rate B/50		215	°C	ISO 306
Vicat Softening Temp, Rate B/120		220	°C	ISO 306
HDT/Be, 0.45MPa Edgew 120104 sp=100mm		210	°C	ISO 75/Be
HDT/Ae, 1.8 MPa Edgew 120104 sp=100mm		205	°C	ISO 75/Ae
Relative Temp Index, Elec	¹⁾	105	°C	UL 746B
Relative Temp Index, Mech w/impact	¹⁾	105	°C	UL 746B
Relative Temp Index, Mech w/o impact	¹⁾	105	°C	UL 746B
PHYSICAL
Mold Shrinkage on Tensile Bar, flow		0.1-0.3	%	SABIC method
Density		1.68	g/cm³	ISO 1183
Water Absorption, (23°C/saturated)		0.7	%	ISO 62-1
Moisture Absorption (23°C / 50% RH)		0.3	%	ISO 62
Melt Volume Rate, MVR at 360°C/5.0 kg		5	cm³/10 min	ISO 1133
ELECTRICAL
Volume Resistivity		1.E+15	Ω.cm	IEC 60093
Surface Resistivity, ROA		>1.E+15	Ω	IEC 60093
Relative Permittivity, 1 MHz		6.2	-	IEC 60250
Dissipation Factor, 50/60 Hz		0.013	-	IEC 60250
Dissipation Factor, 1 MHz		0.022	-	IEC 60250
Comparative Tracking Index	²⁾	200	V	IEC 60112
Comparative Tracking Index, M	²⁾	100	V	IEC 60112
Relative Permittivity, 50/60 Hz		6.8	-	IEC 60250
Comparative Tracking Index (UL) {PLC}		4	PLC Code	UL 746A
INJECTION MOLDING
Drying Temperature		150	°C
Drying Time		4-6	Hrs
Maximum Moisture Content		0.02	%
Melt Temperature		370-415	°C
Nozzle Temperature		360-405	°C
Front - Zone 3 Temperature		370-415	°C
Middle - Zone 2 Temperature		360-405	°C
Rear - Zone 1 Temperature		350-395	°C
Hopper Temperature		80-120	°C
Mold Temperature		140-180	°C

为您推荐

ULTEM AR9200 20%玻璃纤维填充，标准流量聚醚酰胺 ¥78.00
ULTEM AR9300 30%玻璃纤维 ¥87.00
ULTEM ATX200 高流动性聚醚酰亚胺 ¥118.00
ULTEM ATX200F 符合美国食品药品监督管理局食品接触标准。 ¥180.00
ULTEM ATX200R 脱模功能的高流动性聚醚酰亚胺 ¥118.00
ULTEM ATX3562R 50%玻璃纤维和矿物填充的高流动性聚醚酰亚胺 ¥118.00

ULTEM CRS5001 透明、标准流动聚醚酰胺共聚物 ¥180.00
ULTEM CRS5011 透明、增强流动性的聚醚酰胺 ¥180.00
ULTEM CRS5011R 强酸、碱、芳烃和酮的耐化学性 ¥180.00
ULTEM CRS5111 10%玻璃纤维填充的增流聚醚酰胺 ¥180.00
ULTEM CRS5201 20%玻璃纤维填充的标准流动聚醚酰胺 ¥180.00
ULTEM CRS5211R 20%玻璃纤维填充，增强流动性聚醚酰胺共聚物 ¥180.00

供应商网> 特种塑料> ULTEM 4000 聚四氟乙烯和石墨填充的标准流量聚醚酰亚胺

在线问

产品参数

是否进口否
厂家(产地)中国
牌号4000
用途级别注塑

1/2

¥98.00 在线咨询

进店客服获取最低报价拨打电话

ULTEM 4000 聚四氟乙烯和石墨填充的标准流量聚醚酰亚胺: ¥98.00