热稳定15%GF增强PA6 Grilon XE 5052
¥28.50
50%玻纤增强PPA GRIVORY G4V-5H
¥48.50
40%矿物增强PPA GRIVORY GM-4H
¥48.50
20%玻纤PPA GRIVORY GV-2H
¥49.50
瑞士EMS高抗冲40%玻纤PA6 Grilon XE 5051
Density | 1.43 | -- | g/cm | ISO 1183 |
Molding Shrinkage | ISO 294-4 | |||
Across Flow | 0.50 | -- | % | |
Flow | 0.10 | -- | % | |
Water Absorption | ISO 62 | |||
Saturation, 23°C | 5.0 | -- | % | |
Equilibrium, 23°C, 50% RH | 1.5 | -- | % | |
| Hardness | Dry | Conditioned | Unit | Test Method |
Ball Indentation Hardness | 220 | 120 | MPa | ISO 2039-1 |
| Mechanical | Dry | Conditioned | Unit | Test Method |
Tensile Modulus | 11000 | 7500 | MPa | ISO 527-2 |
Tensile Stress(Break) | 170 | 115 | MPa | ISO 527-2 |
Tensile Strain(Break) | 3.5 | 8.0 | % | ISO 527-2 |
| Impact | Dry | Conditioned | Unit | Test Method |
Charpy Notched Impact Strength | ISO 179/1eA | |||
-30°C | 19 | 15 | kJ/m | |
23°C | 25 | 35 | kJ/m | |
Charpy Unnotched Impact Strength | ISO 179/1eU | |||
-30°C | 85 | 80 | kJ/m | |
23°C | 100 | -- | kJ/m |
| Thermal | Dry | Conditioned | Unit | Test Method |
Heat Deflection Temperature | ||||
1.8 MPa, Unannealed | 205 | -- | °C | ISO 75-2/A |
8.0 MPa, Unannealed | 120 | -- | °C | ISO 75-2/C |
Continuous Use Temperature | ||||
--2 | 90.0 to 120 | -- | °C | ISO 2578 |
--3 | 160 | -- | °C | Internal Method |
Melting Temperature4 | 222 | -- | °C | ISO 11357-3 |
CLTE | ISO 11359-2 | |||
Flow | 2.0E-5 | -- | cm/cm/°C | |
Transverse | 6.0E-5 | -- | cm/cm/°C |
| Electrical | Dry | Conditioned | Unit | Test Method |
Surface Resistivity | -- | 1.0E+12 | ohms | IEC 60093 |
Volume Resistivity | 1.0E+14 | 1.0E+14 | ohms·cm | IEC 60093 |
Electric Strength | 41 | 37 | kV/mm | IEC 60243-1 |
Comparative Tracking Index | -- | 550 | V | IEC 60112 |
| Flammability | Dry | Conditioned | Unit | Test Method |
Flammability Classification(0.8 mm) | HB | -- | IEC 60695-11-10, -20 |
PA6干燥处理
干燥处理：由于PA6很容易吸收水分，因此加工前的干燥特别要注意，如果材料是用防水材料包装供应的，则容器应保持密闭。如果湿度大于0.2%，建议在80℃以上的热空气中干燥16小时。如果材料已经在空气中暴 露超过8小时，建议进行温度为105℃，8小时以上的真空烘干。融化温度：230-280℃，对于增强品种为250-280℃。模具温度：80-90℃。模具温度很***地影响结晶度，而结晶度又影响着塑件的机械特性。
在线问
