The IC693ALG220 is a Channel Analog Voltage Input module for the Series 90-30. This Programmable Logic Controller delivers four input channels, each able to convert an analog input signal to a digital signal as needed by the user. The module can convert inputs in the range of -10 to +10 volts. Conversion speed for each channel is 1 ms, thus providing an update rate of 4 ms for any channel. Converted signal resolution is 12 bits binary. User data in the %AI registers is in 16-bit 2’s complement format.
This input module is equipped with a limited current input mode and a jumper on the user terminal connector for each channel. The latter can be used to connect the internal 250 ohm shunt resistor to the circuit. The shunt resistor allows a –40 to +40 mA current input range. It is important, however, for the user to monitor input current to avoid self-heating of the input resistor. Otherwise, current accuracy could be negatively affected. The primary power source for the IC693ALG220comes from the ***lated +24 VDC power supplied via the PLC power supply. Voltage is sent through an inverter/regulator to yield operating voltages for the module. The IC693ALG220 uses 27 mA from the +5 VDC output of the PLC power supply.
This module is also equipped with an LED to alert the user regarding operation. This LED is conveniently located near the top of the faceplate. During normal operation, the LED will emit the ON status. Utilizing optical ***lation, this module creates electrical ***lation of external noise between field wiring and the backplane. To reduce the capacitive loading and noise, it is recommended that the module’s field connections be wired using an appropriate grade of twisted/shielded instrumentation cable.
No. of channels:
4 Inputs
Voltage Range:
-10 to +10 volts DC
Calibration:
Factory calibrated
Update Rate:
4 msec
Input Filter Response:
17 Hz
Power Consumption:
27 mA from +5V bus and 98 mA from +24V bus
-----------------------------------
主营产品：
Foxbore: I / a series system, FBM full series (field I / O module) Sequence control, ladder logic control, accident recall processing, digital to analog conversion, input / output signal processing, data communication and processing, etc. Vestinghouse (Westinghouse): spare parts for 1c31 series DCS system, CPU, ovati0n system, WDPF system and westation system. Triconex: redundant fault-tolerant control system, modern fault-tolerant controller based on triple module redundancy (TMR) structure. Emerson: modules, cards, drives and other spare parts. Xycom: xvme series Bently: 3500 / 3300 system. Rockwell: ICs system.; ABB: PM full series DCS system, ICT high voltage frequency converter series, dsqc series of industrial robot spare parts, infi 90, etc. Bailey: BRC series DCS system, etc. Allen Bradley: 1756, 1785, 1771, 1746 series systems, etc. Yokogawa (Yokogawa): CP series, etc. Honeywell: TK / TC / CC system, etc. Reliance: 57c series, etc. Modicon: as series PLC system spare parts. Moore, a West sub CNC system, etc. Motorola: mvme 162, mvme 167, myvme1772, mvme177 and other series. Xycom: I / 0, vmee board, processor, etc. Ge (General Electric): ic698 / ic697 full range of PLC systems, modules, cards, drives and other spare parts. YASKAWA: servo controller, servo motor, servo driver. Bosch Rexroth: indramat, I / O module, motor, PLC controller, drive module, etc. Woodward: SPC valve position controller, peak150 digital controller.
The GE Fanuc 90-30 IC693BEM331 Genius Bus Controller (GBC) is the interface between a Series 90-30 PLC and a Genius I/O serial bus. The Fanuc 90-30 IC693BEM331 accepts and transmits control data of up to 128 bytes for up to 31 devices on the Genius I/O bus. Up to eight GE IC693BEM331 modules are capable of being included in a Series 90-30 PLC system that has release 5.0 or later Logicmaster 90-30 software, and release 5.0 or later CPU firmware.
通用GE电气HE693STG884工控应用DCS系统模块
¥1352.00
