XPSMF2DO1602安全远程输出模块有16个继电器输出。每个
输出有自己的LED指示灯，指示输出的状态。
模块的每个输出都配有两个分集式安全继电器
导向触点和一个标准型继电器。内部保险丝用于限制
输出触点的开关电流为允许电流的60%（3.15 A）
值（根据VDE 0116，En 298）。触点输出可用于安全
关闭。对于直流开关，触点电路必须另外配备：
适用于容许电流的外部保险丝。
断电时，输出处于安全状态。如果发生故障，所有输出均为
关闭。如果模块有故障，则所有输出都将关闭。如果
故障，在以太网通信时，相关输出设置为初始值。怎样
必须考虑执行机构在这种情况下的响应。
一个或多个通道中的故障以及模块上的故障由指示
远程输出模块前板上的故障指示灯。
继电器输出连接到以下端子：
端子号***功能（输入）
1 DO1触点1，端子A
2触点1，端子B
3 DO2触点2，端子A
4触点2，端子B
5 DO3触点3，端子A
6触点3，端子B
7 DO4触点4，端子A
8触点4，端子B
9 DO5触点5，端子A
10触点5，端子B
11 DO6触点6，端子A
12触点6，端子B
13 DO7触点7，端子A
14触点7，端子B
15 DO8触点8，端子A
16触点8，端子B
17 DO9触点9，端子A
18触点9，端子B
19 DO10触点10，端子A
20触点10，端子B
应用和功能
28 33003411 07/2007
输出触点通过端子连接器成对连接，端子
编号。模块前板上的端子引脚相同
编号顺序，以防止混淆连接。
终端连接符合IP 20的保护要求
更高的要求：模块必须封装在外壳中，带有合适的
保护程度。
为了连接SELV和PELV以外的电压，必须使用合适的电缆
与双绝缘或加强绝缘（如干线电缆）一起使用。
21 DO11触点11，端子A
22触点11，端子B
23 DO12触点12，端子A
24触点12，端子B
25 DO13触点13，端子A
26触点13，端子B
27 DO14触点14，端子A
28触点14，端子B
29 DO15触点15，端子A
30触点15，端子B
31 DO16触点16，端子A
32触点16，端子BThe XPSMF2DO1602 safety remote output module has sixteen relay outputs. Each output has its own LED to indicate the status of the output. Each output of the module is fitted with two safety relays in diversity with positively guided contacts and one standard type relay. Internal fuses are used to limit the switching current of the output contacts to 60% (3.15 A) of the maximum admissible value (according to VDE 0116, En 298). The contact outputs can be used for safety shutdowns.For DC switching the contact circuit must be additionally equipped with an external fuse adapted to the maximum admissible current. An output is in a safe state when it is de-energized. If a fault occurs, all outputs are switched off. If the module has a fault all outputs are switched off. In the event of a fault, at Ethernet communication the relevant output is set to the initial value. How actuators respond in such a cast must be taken into consideration. Faults in one or more channels as well as a fault on the module are indicated by the FAULT LED on the front plate of the remote output module. The relay outputs are connected to the following terminals: Terminal No. Designation Function (Inputs) 1 DO1 contact 1, terminal A 2 contact 1, terminal B 3 DO2 contact 2, terminal A 4 contact 2, terminal B 5 DO3 contact 3, terminal A 6 contact 3, terminal B 7 DO4 contact 4, terminal A 8 contact 4, terminal B 9 DO5 contact 5, terminal A 10 contact 5, terminal B 11 DO6 contact 6, terminal A 12 contact 6, terminal B 13 DO7 contact 7, terminal A 14 contact 7, terminal B 15 DO8 contact 8, terminal A 16 contact 8, terminal B 17 DO9 contact 9, terminal A 18 contact 9, terminal B 19 DO10 contact 10, terminal A 20 contact 10, terminal B Application and Function 28 33003411 07/2007 The output contacts are connected in pairs via terminal connectors, the terminals are numbered. The terminal pins on the front plate of the module have the same numbering sequence in order to prevent confusing connections. The terminal connections meet the protection requirements according to IP 20. For higher requirements the module must be enclosed in a housing with a suitable degree of protection. For the connection of voltages besides SELV and PELV suitable cables must be used with double or reinforced insulation (e.g. mains cable). 21 DO11 contact 11, terminal A 22 contact 11, terminal B 23 DO12 contact 12, terminal A 24 contact 12, terminal B 25 DO13 contact 13, terminal A 26 contact 13, terminal B 27 DO14 contact 14, terminal A 28 contact 14, terminal B 29 DO15 contact 15, terminal A 30 contact 15, terminal B 31 DO16 contact 16, terminal A 32 contact 16, terminal B
在线问
