取消
搜索
搜索
  • 商品
  • 详情

ULTEM 2100R 10%玻璃纤维填充，标准流量聚醚酰亚胺
参数
  • 否是否进口
  • 中国厂家(产地)
  • 2100R牌号
广东 东莞 不限
东莞市聚浩塑化有限公司 2年
进入店铺 在线咨询
产品详情

PROPERTIES
TYPICAL VALUESUNITSTEST METHODS
FLAME CHARACTERISTICS1)


UL Yellow Card Link
E121562-502535--
UL Yellow Card Link 2
E121562-100732300--
UL Recognized, 94-5VA Flame Class Rating
≥1.9mmUL 94
UL Recognized, 94V-0 Flame Class Rating
≥0.41mmUL 94
UV-light, water exposure/immersion
F1-UL 746C
Glow Wire Flammability Index 960°C, passes at2)3.2mmIEC 60695-2-12
Oxygen Index (LOI)
46%ISO 4589
MECHANICAL



Taber Abrasion, CS-17, 1 kg
15mg/1000cySABIC method
Tensile Stress, break, 5 mm/min
115MPaISO 527
Tensile Strain, break, 5 mm/min
4%ISO 527
Tensile Modulus, 1 mm/min
4500MPaISO 527
Flexural Stress, break, 2 mm/min
185MPaISO 178
Flexural Modulus, 2 mm/min
4500MPaISO 178
Ball Indentation Hardness, H358/30
140MPaISO 2039-1
IMPACT



Izod Impact, unnotched 80*10*4 +23°C
30kJ/m²ISO 180/1U
Izod Impact, unnotched 80*10*4 -30°C
30kJ/m²ISO 180/1U
Charpy Impact, notched, 23°C
7kJ/m²ISO 179/2C
THERMAL



Thermal Conductivity
0.24W/m-°CISO 8302
CTE, 23°C to 150°C, flow
3.0E-051/°CISO 11359-2
CTE, 23°C to 150°C, xflow
5.1E-051/°CISO 11359-2
Ball Pressure Test, 125°C +/- 2°C
PASSES-IEC 60695-10-2
Vicat Softening Temp, Rate A/50
223°CISO 306
Vicat Softening Temp, Rate B/50
212°CISO 306
Vicat Softening Temp, Rate B/120
217°CISO 306
HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm
210°CISO 75/Be
HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm
205°CISO 75/Ae
Relative Temp Index, Elec1)170°CUL 746B
Relative Temp Index, Mech w/impact1)170°CUL 746B
Relative Temp Index, Mech w/o impact1)170°CUL 746B
PHYSICAL



Mold Shrinkage on Tensile Bar, flow
0.4-0.6%SABIC method
Density
1.34g/cm³ISO 1183
Water Absorption, (23°C/saturated)
1%ISO 62-1
Moisture Absorption (23°C / 50% RH)
0.6%ISO 62
Melt Volume Rate, MVR at 360°C/5.0 kg
9cm³/10 minISO 1133
ELECTRICAL



Volume Resistivity
1.E+15Ω.cmIEC 60093
Surface Resistivity, ROA
>1.E+15ΩIEC 60093
Dielectric Strength, in oil, 0.8 mm
34kV/mmIEC 60243-1
Dielectric Strength, in oil, 1.6 mm
27kV/mmIEC 60243-1
Dielectric Strength, in oil, 3.2 mm
15kV/mmIEC 60243-1
Relative Permittivity, 1 MHz
2.9-IEC 60250
Dissipation Factor, 50/60 Hz
0.0009-IEC 60250
Dissipation Factor, 1 MHz
0.0025-IEC 60250
Dissipation Factor, 2450 MHz
0.0046-IEC 60250
Comparative Tracking Index2)150VIEC 60112
Comparative Tracking Index, M2)100VIEC 60112
Relative Permittivity, 50/60 Hz
3-IEC 60250
Comparative Tracking Index (UL) {PLC}
4PLC CodeUL 746A
Hot-Wire Ignition (HWI), PLC 1
≥3mmUL 746A
Hot-Wire Ignition (HWI), PLC 2
≥1.5mmUL 746A
High Amp Arc Ignition (HAI), PLC 3
≥1.5mmUL 746A
High Amp Arc Ignition (HAI), PLC 4
≥3mmUL 746A
High Voltage Arc Track Rate {PLC}
2PLC CodeUL 746A
Arc Resistance, Tungsten {PLC}
6PLC CodeASTM D495
INJECTION MOLDING



Drying Temperature
150°C
Drying Time
4-6Hrs
Maximum Moisture Content
0.02%
Melt Temperature
370-410°C
Nozzle Temperature
350-405°C
Front - Zone 3 Temperature
360-415°C
Middle - Zone 2 Temperature
350-405°C
Rear - Zone 1 Temperature
340-395°C
Hopper Temperature
80-120°C
Mold Temperature
140-180°C


为您推荐
供应商网> 特种塑料> ULTEM 2100R 10%玻璃纤维填充，标准流量聚醚酰亚胺
    在线问
    产品参数
    1/2
    ¥98.00 在线咨询
    进店 客服 获取最低报价 拨打电话
    ULTEM 2100R 10%玻璃纤维填充，标准流量聚醚酰亚胺
    ¥98.00
    • 采购产品
    • 采购数量
    • 联系电话
    《服务条款》 并允许推荐更多供应商为您服务
    请阅读并同意《服务条款》

    获取成功

    请您注意近期来电

    看这里，您也可以拨打电话咨询产品哦~

    咨询电话：𐃸𐃹𐃸 𐃺𐃻𐃼𐃼 𐃽𐃼𐃽𐃹

    关闭 产品推荐
    知道了