产品类别:模块卡件
品牌:DCS、PLC
电话:15270269218
联系人:叶经理
质保期:1年
加工定制:不可定制
产地/厂家:美国
F6.06定义了一个完整的横向操作循环
包括上升和下降过程。
注:
在横向模式下,不要选择自动Acc/Dec操作
模式,否则横向运行循环将为
不正常的
F6.07三角形上升时间
波动
范围:0~100.0%【50.0%】
导线运行上升时间=F6.06×F6.07。
导线作业下降时间=F6.06×(1-F6.07)
单位是***。参见图5-37。
注:
您可以同时选择导线测量模式和S曲线,因此
遍历操作要平滑得多。
5.8终端功能(F7组)
F7.00多功能端子X1范围:0~43【0】
F7.01多功能终端X2范围:0~43【0】
F7.02多功能终端X3范围:0~43【0】
F7.03多功能端子X4范围:0~43【0】
F7.04多功能端子X5范围:0~43【0】
F7.05多功能终端X6范围:0~43【0】
F7.06多功能终端X7范围:0~47【0】
F7.07多功能终端X8范围:0~48【0】
多功能输入端子X1~X8的功能为:
广阔的您可以根据以下条件选择X1~X8的函数:
通过设置F7.00~F7.07应用程序。请参阅
表5-5。
表5-5多功能选择
设置功能
0无功能
1预设频率1
2预设频率2
3预设频率3
4 Acc/Dec时间1
第5章参数介绍61
EV2000系列通用变速驱动用户手册
设置功能
5 Acc/Dec时间2
6.外部故障信号常开输入
7.外部故障信号常闭输入
8复位信号
9向前点动操作
10个用于反向点动操作的外部端子
11滑行停止(FRS)
12频率上升(up)
13频率缓降(DN)
14.暂停PLC操作
15 Acc/Dec禁止
16三线操作控制
17外部中断信号常开
输入
18外部中断信号常闭
输入
19直流注入制动指令(DB)
20闭环禁用
21 PLC禁用
22频率选择器1
23频率选择器2
24频率选择器3
25频率基准通过端子输入
CCI强制
26保留
27.强制启用终端控制模式
28控制模式选择器1
29控制模式选择器2
30预设闭环参考1
31预设闭环参考2
32预设闭环参考3
33开始横向操作
34.重置横向运行状态
35外部停止命令
36保留
37驾驶操作禁止
38保留
39长度清理
40辅助参考频率清除
41重置PLC停止状态
42计数器清零信号输入
43计数器触发信号输入
44.输入长度信号
45脉冲输入
46单相速度测量输入
47速度测量输入SM1(仅设置为
X7)
48速度测量输入SM2(仅适用于X8)
表5-5中列出的功能介绍:
1~3:设定速度基准
最多可通过以下方式设置8个速度基准:
端子K3、K2和K1的开/关组合。
表5-6端子的开/关组合
K3 K2 K1频率设置
断开、断开、常用操作
频率
关闭-关闭-打开预设频率1
关-开-关预设频率2
关闭-打开-预设频率3
开-关-关预设频率4
开启-关闭-开启预设频率5
开-关预设频率6
开启,开启,预设频率7
频率基准将用于MS速度
操作和简单的PLC操作。以MS-speed为例
操作示例:
端子X1、X2和X3的定义:
在将F7.00设置为1、F7.01设置为2和F7.03设置为3之后,
终端X1、X2和X3可用于MS速度
操作,如图5-39所示。
速度7
K3
输出频率。
速度1
速度2
速度3
速度4
速度5
速度6
速度
命令
K1
K2
常见的
操作
频率。
时间
图5-39多步速度运行
在图5-40中,选择了终端控制。操作
方向可由K4和K5控制。常用
工作频率和预设频率1~7可
通过K1、K2的不同开/关组合选择
和K3。
F6.06 defines a complete cycle of traverse operation
including rising and falling processes.
Note:
In traverse mode, do not select auto Acc/Dec operating
mode, otherwise the traverse operating cycle will be
abnormal.
F6.07 Rising time of triangle
wave
Range:0~100.0%【50.0%】
Rising time of traverse operation=F6.06×F6.07.
Falling time of traverse operation=F6.06×(1-F6.07)
The unit is second. Refer to Fig. 5-37.
Note:
You can select traverse mode and S curve at the same, thus
the traverse operation is much more smoother.
5.8 Function of Terminals(Group F7)
F7.00 Multi-function terminal X1 Range:0~43【0】
F7.01 Multi-function terminal X2 Range:0~43【0】
F7.02 Multi-function terminal X3 Range:0~43【0】
F7.03 Multi-function terminal X4 Range:0~43【0】
F7.04 Multi-function terminal X5 Range:0~43【0】
F7.05 Multi-function terminal X6 Range:0~43【0】
F7.06 Multi-function terminal X7 Range:0~47【0】
F7.07 Multi-function terminal X8 Range:0~48【0】
The functions of multi-function input terminal X1~X8 are
extensive. You can select functions of X1~X8 according
to your application by setting F7.00~F7.07. Refer to
Table 5-5.
Table 5-5 Multi-function selection
Setting Functions
0 No function
1 Preset frequency 1
2 Preset frequency 2
3 Preset frequency 3
4 Acc/Dec time 1
Chapter 5 Parameter Introductions 61
EV2000 Series Universal Variable Speed Drive User Manual
Setting Functions
5 Acc/Dec time 2
6 External fault signal normally-open input
7 External fault signal normally-close input
8 RESET signal
9 Forward jog operation
10 External terminals for reverse jog operation
11 Coast-to-stop(FRS)
12 Frequency ramp up (UP)
13 Frequency ramp down(DN)
14 Pause the PLC operation
15 Acc/Dec prohiBit
16 3-wire operation control
17 External interrupt signal normally-open
input
18 External interrupt signal normally-close
input
19 DC injection braking command (DB)
20 Close-loop disabled
21 PLC disabled
22 Frequency selector 1
23 Frequency selector 2
24 Frequency selector 3
25 Frequency reference is input via terminal
CCI forcibly
26 Reserved
27 Terminal control mode is forcibly enabled
28 Control mode selector 1
29 Control mode selector 2
30 Preset close-loop reference 1
31 Preset close-loop reference 2
32 Preset close-loop reference 3
33 Start traverse operation
34 Reset the traverse operating status
35 External stop command
36 Reserved
37 Drive operation prohiBiting
38 Reserved
39 Length clearing
40 Auxiliary reference frequency clearing
41 Reset PLC stopping status
42 Counter’s zero-clearing signal input
43 Counter’s trig signal input
44 Input the signal of length
45 Pulse input
46 Single-phase speed measuring input
47 Speed measuring input SM1(only set for
X7)
48 Speed measuring input SM2(only for X8)
Introductions to functions listed in Table 5-5:
1~3: setting speed reference
Up to 8 speed references can be set through different
ON/OFF combinations of terminals K3, K2 and K1.
Table 5-6 On/Off combinations of terminals
K3 K2 K1 Frequency setting
OFF OFF OFF Common operating
frequency
OFF OFF ON Preset frequency 1
OFF ON OFF Preset frequency 2
OFF ON ON Preset frequency 3
ON OFF OFF Preset frequency 4
ON OFF ON Preset frequency 5
ON ON OFF Preset frequency 6
ON ON ON Preset frequency 7
The frequency references will be used in MS speed
operation and simple PLC operation. Take MS speed
operation for example:
Definitions of terminals X1, X2 and X3:
After setting F7.00 to 1, F7.01 to 2 and F7.03 to 3,
terminals X1, X2 and X3 can be used in MS speed
operation, as shown in Fig. 5-39.
speed7
K3
Output freq.
speed1
speed2
speed3
speed4
speed5
speed6
Speed
command
K1
K2
Common
operating
freq.
Time
Fig. 5-39 Multi-step speed operation
In Fig. 5-40, terminal control is selected. The operating
direction can be controlled by K4 and K5. Common
operating frequency and preset frequency 1~7 can be
selected through different On/Off combinations of K1, K2
and K3.