ULTEM 1100F

¥128.00 ≥25千克起批

参数

否是否进口
中国厂家(产地)
1100F 牌号

发货地广东东莞不限

东莞市聚浩塑化有限公司 2年: 进入店铺在线咨询

ULTEM 2100 10%玻璃纤维填充，标准流量聚醚酰亚胺 ¥128.00

ULTEM 2100R 10%玻璃纤维填充，标准流量聚醚酰亚胺 ¥98.00

ULTEM 2110EPR 10%玻璃纤维填充的高流动性聚醚酰亚胺 ¥98.00

ULTEM 2212R 20%碾磨玻璃填充，增强流动性聚醚酰亚胺 ¥98.00

ULTEM 2300FC 30%玻璃纤维增强的标准流动无定形聚醚酰亚胺 ¥98.00

ULTEM 2312 30%研磨玻璃填充、增强流动性聚醚酰亚胺 ¥98.00

产品详情

PROPERTIES		TYPICAL VALUES	UNITS	TEST METHODS
FLAME CHARACTERISTICS	¹⁾
UL Yellow Card Link		E121562-101048254	-	-
UL Recognized, 94-5VA Flame Class Rating		≥3	mm	UL 94
UL Recognized, 94V-0 Flame Class Rating		≥0.75	mm	UL 94
UL Recognized, 94V-2 Flame Class Rating		≥0.4	mm	UL 94
Glow Wire Flammability Index 960°C, passes at	²⁾	3.2	mm	IEC 60695-2-12
Oxygen Index (LOI)		47	%	ISO 4589
MECHANICAL
Taber Abrasion, CS-17, 1 kg		10	mg/1000cy	SABIC method
Tensile Stress, yield, 50 mm/min		110	MPa	ISO 527
Tensile Stress, break, 50 mm/min		85	MPa	ISO 527
Tensile Strain, yield, 50 mm/min		6	%	ISO 527
Tensile Strain, break, 50 mm/min		10	%	ISO 527
Tensile Modulus, 1 mm/min		3500	MPa	ISO 527
Flexural Stress, yield, 2 mm/min		140	MPa	ISO 178
Flexural Modulus, 2 mm/min		3300	MPa	ISO 178
IMPACT
Izod Impact, notched 80104 +23°C		4	kJ/m²	ISO 180/1A
Izod Impact, notched 80104 -30°C		4	kJ/m²	ISO 180/1A
THERMAL
Thermal Conductivity		0.26	W/m-°C	ISO 8302
CTE, 23°C to 150°C, flow		5.E-05	1/°C	ISO 11359-2
CTE, 23°C to 150°C, xflow		5.E-05	1/°C	ISO 11359-2
Ball Pressure Test, 125°C +/- 2°C		PASSES	-	IEC 60695-10-2
Vicat Softening Temp, Rate A/50		210	°C	ISO 306
Vicat Softening Temp, Rate B/50		200	°C	ISO 306
Vicat Softening Temp, Rate B/120		205	°C	ISO 306
HDT/Be, 0.45MPa Edgew 120104 sp=100mm		200	°C	ISO 75/Be
HDT/Ae, 1.8 MPa Edgew 120104 sp=100mm		185	°C	ISO 75/Ae
Relative Temp Index, Elec	¹⁾	170	°C	UL 746B
Relative Temp Index, Mech w/impact	¹⁾	170	°C	UL 746B
Relative Temp Index, Mech w/o impact	¹⁾	170	°C	UL 746B
PHYSICAL
Mold Shrinkage on Tensile Bar, flow		0.4-0.6	%	SABIC method
Density		1.37	g/cm³	ISO 1183
Water Absorption, (23°C/saturated)		1.2	%	ISO 62-1
Moisture Absorption (23°C / 50% RH)		0.65	%	ISO 62
Melt Volume Rate, MVR at 340°C/5.0 kg		12	cm³/10 min	ISO 1133
ELECTRICAL
Volume Resistivity		1.E+15	Ω.cm	IEC 60093
Surface Resistivity, ROA		>1.E+15	Ω	IEC 60093
Dielectric Strength, in oil, 3.2 mm		17.2	kV/mm	IEC 60243-1
Dissipation Factor, 50/60 Hz		0.0016	-	IEC 60250
Comparative Tracking Index	²⁾	175	V	IEC 60112
Comparative Tracking Index, M	²⁾	125	V	IEC 60112
Relative Permittivity, 50/60 Hz		3.5	-	IEC 60250
Comparative Tracking Index (UL) {PLC}		4	PLC Code	UL 746A
Hot-Wire Ignition (HWI), PLC 1		≥3	mm	UL 746A
Hot-Wire Ignition (HWI), PLC 2		≥0.75	mm	UL 746A
High Amp Arc Ignition (HAI), PLC 3		≥3	mm	UL 746A
High Amp Arc Ignition (HAI), PLC 4		≥0.75	mm	UL 746A
High Voltage Arc Track Rate {PLC}		2	PLC Code	UL 746A
Arc Resistance, Tungsten {PLC}		5	PLC Code	ASTM D495
INJECTION MOLDING
Drying Temperature		150	°C
Drying Time		4-6	Hrs
Maximum Moisture Content		0.02	%
Melt Temperature		360-400	°C
Nozzle Temperature		360-400	°C
Front - Zone 3 Temperature		370-410	°C
Middle - Zone 2 Temperature		360-400	°C
Rear - Zone 1 Temperature		340-380	°C
Hopper Temperature		80-100	°C
Mold Temperature		140-180	°C

为您推荐

ULTEM 4000 聚四氟乙烯和石墨填充的标准流量聚醚酰亚胺 ¥98.00
ULTEM 4002 聚四氟乙烯填充，标准流量聚醚酰胺 ¥98.00
ULTEM 6202 12%二氧化硅填充的标准流量聚醚酰胺共聚物 ¥115.00
ULTEM 9075 高流动性聚醚酰亚胺混合物 ¥118.00
ULTEM 9085 具有低毒性、烟雾 ¥78.00
ULTEM 9090 聚醚酰亚胺混合物，延展性和耐洗涤剂性能得到改善 ¥78.00

ULTEM AR9100 10%玻璃纤维填充，标准流量聚醚酰亚胺 ¥79.00
ULTEM AR9200 20%玻璃纤维填充，标准流量聚醚酰胺 ¥78.00
ULTEM AR9300 30%玻璃纤维 ¥87.00
ULTEM ATX200 高流动性聚醚酰亚胺 ¥118.00
ULTEM ATX200F 符合美国食品药品监督管理局食品接触标准。 ¥180.00
ULTEM ATX200R 脱模功能的高流动性聚醚酰亚胺 ¥118.00

ULTEM ATX3562R 50%玻璃纤维和矿物填充的高流动性聚醚酰亚胺 ¥118.00
ULTEM AUR200G6 PEI ¥180.00
ULTEM AUT195 高流动性聚醚酰亚胺 ¥180.00
ULTEM AUT200 透明高流动性聚醚酰亚胺 ¥118.00
ULTEM AUT200M 透明高流量聚醚酰亚胺 ¥118.00
ULTEM AUT210 透明热塑性聚酰亚胺 ¥180.00

供应商网> 特种塑料> ULTEM 1100F

在线问

产品参数

是否进口否
厂家(产地)中国
牌号1100F
用途级别注塑

1/2

¥128.00 在线咨询

进店客服获取最低报价拨打电话

ULTEM 1100F: ¥128.00